CCNA Discovery 3 Module 5

CCNA Discovery 3
Module 5 Exam Answers Version 4.0
1. What three statements are true about routers that are configured for EIGRP? (Choose three.)
• They can support multiple routed protocols
• They send partial routing updates in response to topology changes.
• They use hello packets to inform neighboring routers of their status.

2. Given the following commands:
Router(config)# router rip
Router(config-router)# network 192.31.7.0
What three conclusions can be determined based on the commands used on the router? (Choose three.)
• A link-state routing protocol is used.
• A distance vector routing protocol is used.
• Routing updates broadcast every 30 seconds.
• Hop count is the only metric used for route selection.

3. What is indicated when an EIGRP route is in the passive state?
• The route is viable and can be used to forward traffic.

4. What two problems may occur if the EIGRP default bandwidth for a serial link is higher than the actual bandwidth? (Choose two.)
• Suboptimal paths will be selected.
• Network convergence may be affected.

5. What is the default administrative distance for EIGRP internal routes?
• 90

6. A network administrator issues the command show ip route and sees this line of output:
192.168.3.0/24 [120/2] via 192.168.2.2, 00:00:05, Serial0/0
What two pieces of information can be obtained from the output? (Choose two.)
• RIP is the routing protocol configured.
• The metric for this route is 2.



7.
alt=1 v:shapes="_x0000_i1025">


Refer to the exhibit. Which statement is true about the EIGRP authentication configuration?
• RTA and RTB will accept updates from each other.

8. Which Layer 4 protocol does EIGRP use to provide reliability for the transmission of routing information?
• RTP

9.


alt=2 v:shapes="_x0000_i1026">


Refer to the exhibit. Routers RTR-1 and RTR-3 are completely configured. The administrator needs to configure the routing protocol on router RTR-2 so that communication occurs throughout the network. Which group of commands will successfully configure EIGRP on RTR-2?
• RTR-2(config)# router eigrp 1
RTR-2(config-router)# network 198.18.76.0

10. What prevents RIPv1 updates from being correctly advertised?
• the use of variable length subnet masks

11. What does a router that is running RIP use to determine the best path to take when forwarding data?
• the calculated metric for the destination network

12. What is the purpose of the network command when RIP is being configured as the routing protocol?
• It identifies the directly connected networks that will be included in the RIP routing updates.

13. How do EIGRP routers establish and maintain neighbor relationships?
• by exchanging hello packets with neighboring routers

14.
alt=3 v:shapes="_x0000_i1027">
Refer to the exhibit. Routers A and B have EIGRP configured and automatic summarization has been disabled on both routers. Which router command will summarize the attached routes?
• ip summary-address eigrp 1 192.168.10.64 255.255.255.192

15. How often does RIPv2 send routing table updates, by default?
• every 30 seconds

16.
alt=4 v:shapes="_x0000_i1028">
Refer to the exhibit. A network administrator is troubleshooting a routing problem. When the show ip route command is entered on RTR-1, only the serial link between RTR-2 and RTR-3 has been learned from the RIP routing protocol. What are two issues? (Choose two.)
• RIPv1 is a classful routing protocol.
• RIPv1 does not support subnetting.
• The Ethernet networks on RTR-2 and RTR-3 were not entered correctly in the network statements on these routers.
• RIPv1 does not support VLSM.
• RIPv1 is a classless routing protocol.

17. What two statements are correct regarding EIGRP authentication? (Choose two.)
• EIGRP authentication uses the MD5 algorithm.
• EIGRP authentication uses a pre-shared key.

18. When should EIGRP automatic summarization be turned off?
• when a network contains discontiguous network addresses

19. What is the maximum number of hops that RIP will attempt before it considers the destination unreachable?
• 15 hops

20. What two statements are true regarding EIGRP tables? (Choose two.)
• A feasible successor route can be found in the topology table.
• The topology table shows whether a route is in the passive or active state.

21.

alt=5 v:shapes="_x0000_i1029">
Refer to the exhibit. Which statement is true about the output from the show ip protocols command?
• RIPv2 is configured on this router.